Just How To Install A Bathtub (For Newbies).
Just How To Install A Bathtub (For Newbies).
Blog Article
On this page below you will find lots of awesome insight all about A Step-by-Step Guide to Installing a Bathtub.
Setting up a bath tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably hard task. If the old tub is readily available, the job can move immediately; if you have to open a wall to eliminate the old tub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Chances are you might require a specialist plumber to make tube connections.
This short article will help you install a new bath tub in your washroom if you have already bought a new bathtub and also do not need to change the arrangement of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be rather troublesome because of the restricted accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be attached to the tap finishes initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the called for position. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub till the level reads level.
To mount faucets, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the supply of water and also examine all joints and new pipework for leaks as well as tighten them if essential. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's user's manual. Tiling as well as securing around the bath tub needs to wait till the bathtub has been used at least once as this will settle it into its final setting.
Getting ready for the Setup
To start with, the sustaining framework provided with the bathroom must be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a rigid seal, creating the water to penetrate the wall surface in between the bath and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture fairly very early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our piece on How to Install a Bathtub Yourself. Thank you for finding the time to read our post. Do you know somebody else who is interested by the subject? Be sure promote it. Thank-you for your time spent reading it.
Instant Quote Report this page